|
Heatmiser UH1
8 Zone Wiring Centre - Compatible with our 12v Network Thermostats
The Heatmiser UH1 is designed to be used in conjunction with our 12v network thermostats.
Underfloor Heating - The UH1 provides central switching and is therefore ideally situated next to the underfloor heating manifold. 8 Zones can be controlled as well as providing an output for a hot water cylinder. On demand from any zone, a 230v output is provided to switch the relevant zone actuators, underfloor heating pump and valve. A volt free connection is supplied for the boiler, making it compatible with almost all types of boilers. Up to 6 actuators can be connected to each zone.
An option is provided to turn zone 8 into a radiator zone. In this mode the underfloor heating pump, valve and boiler are not enabled when there is a call for heat from zone 8.
Radiator System - The UH1 isn't just for underfloor heating. It can equally be used in a radiator only system.
The UH1 provides a network port allowing connection to our network products, including the central Touchpad, Netmonitor and PCLink.
View the Heatmiser UH1 in the Heatmiser Shop
|
 |
Heatmiser UH2
4 Zone Wiring Centre - Compatible with our 230v Thermostats
The Heatmiser UH2 can be used in conjunction with our mains thermostats. The Heatmiser UH2 provides central control switching of up to 4 zone actuators as well as providing an output for a hot water cylinder and the heating system boiler and pump. When used for underfloor heating, an option is available to use zone 4 for conventional radiator control. Up to 6 actuators can be connected to each zone.
Radiator System - The UH2 isn't just for underfloor heating. It can equally be used in a radiator only system.
View the Heatmiser UH2 in the Heatmiser Shop
|
|
Heatmiser UH3
8 Zone Wiring Centre - Compatible with our 230v Thermostats
Our Heatmiser UH3 is designed to work with our 4 channel 230v time clock (TM4) and 230v Set Back thermostat (DS-SB) but equally could be used with any 230v room thermostat. Up to 8 zones can be controlled from the UH3. On board the UH3 are two heating channels, each allows you to specify which time channel it should follow. 2 additonal time channel connections are provided for hot water control or other auxillary devices.
On demand from any zone, a 230v output is provided to switch the relevant zone actuator, underfloor heating pump and valve. A volt free connection is supplied for the boiler, making it compatible with almost all types of boilers.
A simple slide switch makes zone 8 suitable for controlling a radiator zone. When used for controlling radiators, zone 8 does not enable the underfloor heating pump, valve and boiler. Up to 4 actuators can be connected to each zone.
Radiator System - The UH3 isn't just for underfloor heating. It can equally be used in a radiator only system.
View the Heatmiser UH3 in the Heatmiser Shop
|
 |
Heatmiser UH1-W
8 Zone Wireless Wiring Centre - Compatible with our Wireless Thermostats
The Heatmiser UH1-W is designed to be used in conjunction with our compatible wireless thermostats. The UH1-W provides central switching and is therefore ideally situated next to the underfloor heating manifold. 8 zones can be controlled as well as providing an output for a hot water cylinder. On demand from any zone, a 230v output is provided to switch the relevant zone actuators, underfloor heating pump and valve. A volt free connection is supplied for the boiler making it compatible with almost all types of boilers. Up to 6 actuators can be connected to each zone. An external aerial is available for use when the UH1-W is being mounted in a metal cupboard or when the wireless signal is restricted.
A software option is the thermostat allows you to configure which zones are underfloor heating and which zones are radiators. Radiator zones will not enable the underfloor heating pump and valve when there is a call for heat.
View the Heatmiser UH1-W in the Heatmiser Shop
|
 |
|
